The benefits of environmental chamber testing

Environmental test equipment is the general name of all test chambers simulating natural climate environment. Representative products include salt spray test chamber, high and low temperature test chamber, constant temperature and humidity test chamber, UV aging test chamber, xenon lamp aging test chamber, ozone aging test chamber, oven, etc.

The environmental test chamber is one of the necessary test equipment in the plastic, rubber, electronic and other material industries. It is used to test the extent to which the material can withstand the continuous environment of high and low temperature in a short time, so as to obtain the chemical changes or physical damage caused by the thermal expansion and contraction of the test sample, and the weather resistance to the natural environment.

Six benefits of environmental chamber testing:
1. The environmental test chamber has product modeling design, and the actual operation is simple. Colorful touch screen and computer temperature controller are selected. The column type three box structure, the high and low temperature box circulation system, the whole process automatic control system, the retention and change time are adjustable, the stainless steel plate liner, multi-mode recording, and a variety of security measures are set under it.
2. It has perfect alarm function: when abnormal conditions such as over temperature of the working chamber, over pressure of the compressor, short circuit, power failure, water failure, etc. occur during the test, the cause of the fault and troubleshooting methods will be immediately displayed on the screen. If the input voltage is found to be unstable, it has an emergency shutdown device.
3. Expandable equipment of environmental test chamber: temperature recorder LN2 rapid cooling control system RS-232 communication interface device, which can monitor and record local area network at the same time with personal computer.
4. Function module: the equipment is divided into three parts, namely, the test area, high temperature and low temperature area. The unique heat cut-off structure and heat and cold storage effect are adopted, and the cold and hot air switching mode is adopted to introduce into the test sample.
5. It has a high program memory capacity, and can be set to store 100 groups of programs. The large cycle system is set to 9999cycles, and each period of time is 999hrs59minutes With RS-232C communication interface equipment, it can be connected with the computer for online manipulation / writing / recording and ten groups of dynamic connections, which is convenient to use.
6. When implementing the environmental test chamber conditions, you can select the 2Zone or 3ZONE function. It has a fully automatic and high-precision system.

LISUN lauched SC-015 Dust-proof Test Chamber (Sand Dust Chamber) is applied to physical and other related performance tests for electronic and electrical products, lamps, electrical cabinets, electrical components, automobiles, motorcycles and their parts and other products under simulated dust climate conditions. After the measurement, it is judged whether the performance of the product meets the requirements through verification, so as to facilitate the design, improvement, verification and factory inspection of the product. Comply meets IEC60529:1989 +A1:1999 +A2: 2013 <Degrees of protection provided by enclosures (IP Code)>,IEC60598-1,  GB2423.37-89 (Test L: dust test methods), GB4208, GB/T 4942.2-93(protective casing grade of low-voltage apparatus), GB7000.1 <Luminaires Part 1: General Requirements and Tests> 9.2.1, 9.2.2 and Figure 6, DIN40050 and IP5K0. The dust test chamber is applicable to the IP5X and IP6X dustproof test of the products.

SC-015 Dustproof test chamber

Temperature Humidity Chamber | Thermal Chamber | Climate Chamber is according to IEC60068-2-1 (GB/T2423.1) and IEC60068-2-2 (GB/T2423.2), IEC60068-2-78, IEC60598-1, GB/T2423.17, GB/T5170.2, GB/T5170.5. The climate chamber is used to test the CFL/LED which meets IES LM-80-08, electricity products, automative cars, home appications and mobiles.

GDJS-015B High and Low Temperature Humidity Chamber

Salt Spray Test Chamber | Salt Fog Test | ASTM B117 Salt Spray ChamberSalt Spray Test Chamber is applicable to the salt spray corrosive test for the protection layer of components, parts, electronic and electrical parts and metal materials and industrial products. The salt fog test chamber meets the following standards: IEC60068-2-11 (GB/T2423.17), GB/T10125, GB/T1771, ISO9227, ASTM-B117, GB/T2423-18, QBT3826, QBT3827, IEC 60068-2-52, ASTM-B368, MIL-STD-202, EIA-364-26, GJB150, DIN50021-75, ISO3768, 3769, 3770; CNS 3627, 3885, 4159, 7669 etc.

YWX/Q-010_Salt Spray Test Machine

Lisun Instruments Limited was found by LISUN GROUP in 2003. LISUN quality system has been strictly certified by ISO9001:2015. As a CIE Membership, LISUN products are designed based on CIE, IEC and other international or national standards. All products passed CE certificate and authenticated by the third party lab.

Our main products are Goniophotometer, Integrating Sphere, Spectroradiometer, Surge Generator, ESD Simulator Guns, EMI Receiver, EMC Test Equipment, Electrical Safety Tester, Environmental Chamber, Temperature Chamber, Climate Chamber, Thermal Chamber, Salt Spray Test, Dust Test Chamber, Waterproof Test, RoHS Test (EDXRF), Glow Wire Test and Needle Flame Test.

Please feel free to contact us if you need any support.
Tech Dep: Service@Lisungroup.com, Cell/WhatsApp:+8615317907381
Sales Dep: Sales@Lisungroup.com, Cell/WhatsApp:+8618117273997