IPX7 Immersion tank Waterproof test Device test condition standard

IPX7 Immersion tank Waterproof test Device indicates that the waterproof grade of the product is 7. When the product is immersed in water for a short time under standard pressure, it will not enter the interior even if it is immersed in water under specified conditions. It is described in detail in GB 4208. This grade belongs to a higher waterproof grade. It is generally placed in the environment with a water depth of 1 meter and tested for half an hour.

The difference between the water temperature of the IPX7 Immersion tank Waterproof test Device and the sample temperature should not exceed 5 ℃. However, if the sample needs to be tested under live or running conditions, it can be customized after consultation with the manufacturer. In general, the product should be soaked in 1 meter deep water for 30 minutes without water. It can be seen that IPX7 waterproof products can be worn when bathing. If swimming, IPX7 waterproof products should not be worn when swimming due to factors such as immersion time, water impact, water depth, etc.

IPX7 Immersion tank Waterproof test Device is divided into two types, one is stainless steel immersion test device 1; One is a glass-type immersion test device 2. The testing machine can simulate the pressure environment of water depth and conduct water pressure test on the sample.

Glass immersion tester:
1. The testing machine can simulate the water pressure test with a water depth of 0-1200mm, and the standard test time is 30 minutes.

2. The testing machine is made of five pieces of tempered glass and 304 stainless steel, and the equipment is beautiful and generous, and can observe the test situation in the box more comprehensively; Stainless steel is mainly used to connect the joints of tempered glass plates, which can effectively increase the pressure bearing capacity of the chamber.

3. In order to make it easier for operators to know the amount of water in the box, we installed a stainless steel ruler outside the chamber. The value of the stainless steel ruler is measured from the bottom of the chamber, just to measure the amount of water.

4. There are two external water valve switches on the bottom front of the immersion tank, one is the inlet valve; One is the drain valve. This design is convenient for water inlet and outlet of equipment. We also installed movable pulleys for the testing machine to facilitate the movement and handling of the equipment.

Stainless steel immersion tester:
1. The immersion test equipment can simulate the water pressure test with a water depth of 0-1200mm, and the standard test time is 30 minutes;

2. The whole body of the testing machine is made of 304 stainless steel, with high rust resistance. The polished stainless steel plate is beautiful and generous; The inner part of the case has two layers of thick stainless steel plates, which increases the pressure bearing capacity of the equipment.

3. We can install electric hoist or other lifting devices for placing samples for customers; Or weld an iron hook inside the box to facilitate sample extraction.

4. In the middle of the testing machine, we added a piece of toughened glass with a diameter of more than 12mm to facilitate the inspection personnel to see the test conditions inside.

5. The inlet and outlet pipes of the immersion test device are installed under the water tank, and the inlet valve is installed above the back of the tank.

Structure description of IPX7 Immersion tank Waterproof test Device:
1. Tempered glass: fully transparent, can observe the test condition of the test sample; It is durable and watertight for long time use.
2. Stainless steel frame: fix and support glass water tank, firm and reliable.
3. Water level gauge: display the actual water level, and the small scale unit is mm.
4. Water inlet and outlet valve: there are two external water valve switches on the front of the base, one inlet valve and one drain valve.
5. Water inlet and outlet: the water inlet and outlet are under the glass water tank, hidden under the stainless steel base, with water inlet and outlet pipe joints.
6. Castor: easy to move the water tank; The castor has a brake, which can easily fix the water tank.
7. Foot cup: fix and support glass water tank, firm and reliable. Prevent slipping and danger.

Test condition standard of IPX7 Immersion tank Waterproof test Device:
1 The lowest point of the shell with height less than 850mm shall be 1000mm lower than the water surface;
2 The highest point of the shell with a height equal to or greater than 850 mm shall be 150 mm below the water surface
3 Test duration: 30min;
4 The temperature difference between the water temperature and the sample shall not be greater than 5 K. If the test sample needs to be tested under live and/or running conditions, the relevant product standards can make other provisions for this requirement.

How to select the appropriate IPX7 Immersion tank Waterproof test Device?
1. Confirm which waterproof grade test is required for your product. Go to see more parameters or contact customer service directly to see if it is suitable for you.

2. The size of the ipx7 Immersion tank Waterproof test Device. Whether you need to test a small amount or a large amount, its regular dimensions are: 600 * 600 * 600mm, 800 * 800 * 800mm, 1000 * 1000 * 1000mm, 1200 * 1200 * 1200mm, etc. The box can be selected according to the amount of testing every day. Of course, it can also be customized according to the needs of users.

3. The ipx7 Immersion tank Waterproof test Device has two different functions, namely, electric lifting type and electric traverse type. Is the product you are testing a small sample or a large sample? If testing large samples, we can provide customers with electric function, so that large samples can be easily placed and taken out. On the contrary, conventional instruments can be selected for small samples.

JL-X waterproof test machine is according to IEC60529:1989 +A1:1999 +A2：2013 《Degrees of protection provided by enclosures(IP Code)》, IEC60598, IEC60335 and IEC 60034-5, GB/T-2423.2, GB4208, GB7000.1. The JL-X includes the following test grades: IPX1, IPX2, IPX3, IPX4, IPX5, IPX6, IPX7 and IPX8 (Refer to page 51 of IEC60529). It is widely used in the authentication test organization for the products such as electrical & electronic products, LED luminaires as well as in the relevant quality control department for the waterproof detection of the enclosures protection grades.

• Immersion tank Waterproof test Device (JL-7): It is for IPX7 waterproof test. The water tank size is 1000x1000x1200mm (Other size can be designed according to your request). It can test samples up to 120kg. 

Waterproof Test Machine 

Lisun Instruments Limited was found by LISUN GROUP in 2003. LISUN quality system has been strictly certified by ISO9001:2015. As a CIE Membership, LISUN products are designed based on CIE, IEC and other international or national standards. All products passed CE certificate and authenticated by the third party lab.

Our main products are Goniophotometer, Integrating Sphere, Spectroradiometer, Surge Generator, ESD Simulator Guns, EMI Receiver, EMC Test Equipment, Electrical Safety Tester, Environmental Chamber, Temperature Chamber, Climate Chamber, Thermal Chamber, Salt Spray Test, Dust Test Chamber, Waterproof Test, RoHS Test (EDXRF), Glow Wire Test and Needle Flame Test.

Please feel free to contact us if you need any support.
Tech Dep: Service@Lisungroup.com, Cell/WhatsApp:+8615317907381
Sales Dep: Sales@Lisungroup.com, Cell/WhatsApp:+8618117273997