LISUN JL-12CP Waterproof Test Chamber – After Sales Questions and Answers

JL-XC series waterproof test chambers are mainly used for small electronic and electrical products such as lamps, electrical cabinets, electrical components and so one. It is used for physical and other related properties checking under simulated climatic conditions. It determines whether the performance of the product meets the requirements or not after the test. It is very useful in the design, improvement, verification and factory inspection of the product. The JL-XC waterproof testing fully meets IEC60598-1,  IEC60529:1989 +A1:1999 +A2：2013 《Degrees of protection provided by enclosures(IP Code)》, GB4208-2008 and GB7000.1.

Features:
• The outer casing is made of high-quality steel plate, and the surface is painted with paint which is beautiful and durable. The inner box, the turntable, and the wading part are all made of SUS304 stainless steel plate to make sure that it will not rust after using for a long time. (Inner box sheet thickness: 1.2mm, can handle the water pressure)
• IPX12: The compressed air drying function can remove the excess water in the drip tank after the test to avoid long-term water accumulation and fouling. (User need to provide air compressor)
• IPX34: The driver for the swing pipe adopts high-quality servo stepping motor, the swinging speed and angle are precisely adjustable. There is no out-of-step problem (the risk of out-of-step: it will cause the swinging tube to malfunction, hitting the middle turntable shaft, causing equipment damage)
• IPX56: It is with monolithic structure. The sray gun direction is adjustable and can be fixed. The operator only need to start the test but no need to carry the spray gun.
• The water supply line is equipped with a filter to filter impurities in the water to prevent nozzle clogging.
• The LED waterproof lighting is installed in the chamber, and there is a large observation window on the door to facilitate the observation of the test sample.
• The equipment equipped with a water tank for recycling water, no need building a professional waterproof test room. The water tank float valve in the water tank automatically controls the water inlet, and has high and low water level alarm monitoring to effectively prevent the pump from being damaged due to running out of water.
• The turntable uses a stepper motor, the speed can be set on the touch screen, and can control the forward and reverse rotation (suitable for the sample power-on test to prevent winding).
• Touch screen control function: Directly select the waterproof level on the self-developed IPX waterproof level test operation interface. You can run test according to the waterproof rating conditions in the standard terms easily.
• Test sample input power: single-phase 220V/10A (other specifications can be customized)
• Equipment power supply frequency: Default is 50Hz and 60Hz is also available (It is very important to confirm us your grid power frequency) 

Q1: why does jl-12 equipment use air compressor
A1: The air compressor is an auxiliary equipment, and it is not necessary to use the air compressor during the test. Only after the test is completed, use the air pressure of the air compressor to quickly remove all the water in the drip tray. Therefore, if there is no air compressor, the test can be carried out normally.

Note: If you need to use the air compressor, please remove one or two needles from the drip tray first, and then start the air compressor. In order to avoid the danger of loose needle caused by too large air pressure in the drip tray.

Q2: How to avoid sample power cord winding
A2: During the test, the turntable needs to rotate. However, the turntable designed by us will automatically rotate in the opposite direction every minute to avoid the winding of the sample power cord. Use our standard waterproof plug power cord.

Q3: How to confirm test results
A3: If the sample is short circuited and extinguished during the test, it must not meet the standard. If the sample can still be lit normally, it is necessary to take out the sample, wipe the water on the surface, and then open the sample to check whether there is water inside. If there is water, it is also not in conformity with the standard.

For specific details, the rules are different in different industries. Please refer to the corresponding industry standards.

Lisun Instruments Limited was found by LISUN GROUP in 2003. LISUN quality system has been strictly certified by ISO9001:2015. As a CIE Membership, LISUN products are designed based on CIE, IEC and other international or national standards. All products passed CE certificate and authenticated by the third party lab.

Our main products are Goniophotometer, Integrating Sphere, Spectroradiometer, Surge Generator, ESD Simulator Guns, EMI Receiver, EMC Test Equipment, Electrical Safety Tester, Environmental Chamber, Temperature Chamber, Climate Chamber, Thermal Chamber, Salt Spray Test, Dust Test Chamber, Waterproof Test, RoHS Test (EDXRF), Glow Wire Test and Needle Flame Test.

Please feel free to contact us if you need any support.
Tech Dep: Service@Lisungroup.com, Cell/WhatsApp:+8615317907381
Sales Dep: Sales@Lisungroup.com, Cell/WhatsApp:+8618117273997

Tags：JL-CP